small creaturesa field guide to the insects and spiders in NZ homes and gardens

The common house borer: what the beetle and its holes look like

entry no. 20 · 2026-11-20

The common house borer is a small beetle, brown and about the size of a grain of rice, that spends most of its life as a larva inside the sapwood of timber. The beetle itself is seldom seen. What people actually find are the holes it leaves behind, little round pinpricks in floorboards, weatherboards, joists and old furniture. Because several other wood-boring insects make holes that look similar, a careful look at the size and shape of the damage is the first step in knowing what you have.

The beetle

The common house borer is Anobium punctatum, an anobiid beetle found through temperate regions of the world, including New Zealand. According to Scion's Forest and Timber Insects in New Zealand series, which is reproduced by the NZ Farm Forestry Association, the adult is 2.5 to 5 mm long, with females usually larger than males. It is reddish to blackish brown, cylindrical in shape, and the front of the thorax forms a deep hood that covers the head when seen from above. The wing cases carry rows of fine punctures, and the body is covered with short yellow hairs.

Adults are short-lived. They emerge from the timber between November and January, according to the Scion account, live for about four weeks, and do not feed. In that time the females lay eggs, which are small, white and tucked into rough-sawn surfaces, cracks and crevices, or old exit holes.

The larva: where the damage happens

The eggs hatch after four to five weeks, and the creamy-white, C-shaped larvae, up to 7 mm long, bore into the wood. Scion says they prefer sapwood. Development is slow: egg to adult takes about three years in kahikatea sapwood and four years in rimu and radiata pine sapwood, speeding up when the humidity is above 70 percent and temperatures are warm. The larvae then pupate in chambers just below the surface for four to eight weeks, before chewing out.

This long life underground explains why borer is often found by accident. The wood can be riddled with tunnels long before the first beetles appear, and the exit holes are the point at which the damage becomes visible.

The holes and the dust

The signature feature is the exit hole: small, round, about 1 to 2 mm across. They tend to be numerous and scattered over the surface. BRANZ's Renovate series, in its bungalows volume, uses this as the basic way to distinguish the two borers most commonly met in older houses. The common house borer leaves many small round holes, whereas the two-tooth longhorn borer (Ambeodontus tristis) leaves fewer, larger oval holes that can reach 5 mm long.

Beneath the holes there is often a little bore dust, called frass. Scion describes it as loosely packed and granular, with a gritty feel when rubbed between the fingers. It can dribble out of the exit holes when disturbed by emerging beetles, parasites or vibration.

Which timbers

The borer attacks sapwood, not the dense heartwood in the middle of a board. Scion notes that kahikatea is especially favoured, along with rimu and radiata pine, while Douglas fir and western red cedar suffer very little. It goes for untreated timber in structural framing, exterior cladding, joinery, furniture and flooring. BRANZ adds that borer damage is more likely where sapwood has become damp in service, and that the common house borer's attack generally tends to stop before timber becomes structurally unsound, because most framing timber has enough heartwood to avoid serious weakening.

Scion records that the use of preservative-treated timber has greatly reduced infestations in modern houses. Older houses built from untreated native timber, especially subfloors and dampish corners, are where they are still found.

Look-alikes

Not every small round hole is the common house borer. The NZ Farm Forestry Association's index lists a native household borer, Leanobium flavomaculatum, and another native anobiid, Hadrobregmus magnus. A third insect, the pine bark anobiid (Ernobius mollis), makes flight holes that are usually about 2 mm across and are often mistaken for those of the household borer. Its wing cases are smooth, whereas the house borer's have rows of pits, and its larvae look so similar that larvae alone are hard to separate.

The practical lesson is that hole size alone does not give a species. The beetle, the frass and the timber it is in all help, and a specialist can identify the borer from a sample. Be wary of confident identification based on a single photo of a hole.

When a closer look is worth it

A scattering of old holes in a piece of furniture is rarely urgent. A cluster of holes in a bearer, joist or floor timber in a damp subfloor deserves attention, since sapwood framing in damp conditions is exactly where damage is most likely to matter. Because moisture is what makes sapwood vulnerable, damp and borer are usually assessed together. For a plain-language description of this beetle from a timber inspection firm's reference library, see the house borer entry, which sets out what an inspector looks for.

What to do next

If you have found holes and are unsure what they mean, note the size, how many there are, and where on the timber they appear. Photograph them next to a ruler. A timber pest inspector such as Lignum Timber Inspections can examine the timber, identify the species and assess the extent of any damage.

Sources

next entry → The German wasp year: queen to nest to collapse